- whatsapp +51955515985
- support@ecuforcetruck.com
- 24/7 Customer Support
Menu
Shop
Account
Subtotal: $0.00
No products in the cart.
Circuit Description
The engine control module (ECM) provides a 5 volt supply to the fuel rail pressure sensor using a dedicated sensor supply circuit. The ECM also provides a ground on the sensor return circuit. The fuel rail pressure sensor provides a primary fuel pressure signal to the ECM on the fuel rail pressure sensor signal 1 circuit. The sensor also provides a secondary fuel pressure sensor signal on the fuel rail pressure signal 2 circuit. This sensor signal voltage changes based on the pressure in the fuel rail. The ECM will detect a high signal voltage at high rail pressure conditions. The ECM will detect a low signal voltage during low rail pressure conditions.
Component Location
The high-pressure fuel pump is mounted to the gear housing. The fuel pump actuator is mounted on the fuel pump. The fuel pressure sensor is mounted in the high pressure fuel rail. The fuel pressure relief valve is mounted on the high pressure fuel rail.
Conditions for Running the Diagnostics
This diagnostic runs when the engine is being started.
Conditions for Setting the Fault Codes
The Engine Control Module (ECM) detected the fuel rail pressure during cranking was too low for the engine to start.
Action Taken When the Fault Code is Active
The ECM illuminates the amber CHECK ENGINE lamp and/or the Malfunction Indicator Lamp (MIL) immediately when the diagnostic runs and fails.
The engine may not start.
Conditions for Clearing the Fault Code
To validate the repair, perform a key cycle, start the engine and let it idle for 1 minute.
The fault code status displayed by INSITE™ electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.
The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
For On-Board Diagnostics (OBD) engines, the ECM will extinguish the Malfunction Indicator Lamp (MIL) after three consecutive trips where the diagnostic runs and passes.
The Reset All Faults command in INSITE™ electronic service tool can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.
Shop Talk
Possible causes of this fault code include:
A malfunctioning fuel lift pump
Low fuel gear pump output pressure
Malfunctioning high-pressure fuel pump
Leaking fuel rail pressure relief valve
Leaking fuel injectors and or fuel injector connectors
Possible Cause:
1) Loose Injector High-Pressure connector
2) Fuel rail pressure relief valve failure
3) High-Pressure fuel pump head failure
4) ECM calibration
Related
Categories Cumminz, DTC TRUCKS, Tags , 1, 18, 2018, 4691, 5585, Below, But, CM2450, Code, Cranking, Cummins, Data, Engine, Fault, FMI, Injector, Level, Metering, Moderately, Newer, Normal, Operating, PID, Pressure-, Rail, Range-, Severe, SPN, Valid, X124B, X15
Wiring Diagrams
Component Locators
- Bendix Acom Pro 2023 V1 diagnostic software 1PC
Bendix$83.00
Rated 0 out of 5
PF Diagnose$60.00
Rated 0 out of 5
- Nexiq eTechnician 2.0.7447 2020
NEXIQ$55.00
Rated 0 out of 5
- NEXIQ eTechnician 2.1.7657.26963 + Patch 2020
Allison$60.00
Rated 0 out of 5
- VOLVO PTT TECH TOOL 2.8.220 2023 Last version 1pc
Trucks software$200.00
Rated 0 out of 5
- Bobcat Software Service Analyzer Version 87.07 ( 1PC )
Bobcat$90.00
Rated 0 out of 5
Trucks software$55.00
Rated 0 out of 5
- Hino Diagnostic eXplorer 2 – Hino DX2 v1.1.21.4 with keygen unlocked ( Hino trucks )
Hino$60.00
Rated 0 out of 5
- Perkins SPI2 2018A Dealer Parts and Service
Perkins$50.00
Rated 0 out of 5
- Nexiq eTechnician 1.3.62 2020 etechnician software
NEXIQ$50.00
Rated 0 out of 5
- Wabco PIN Code Calculator Diagnostic Software PIN 1 PIN 2
Trucks software$10.00
Rated 0 out of 5
- Detroit Diagnostic Link (DDDL 8.09) Engineering level 10
Detroit$40.00
Rated 0 out of 5
- 2021 VOLVO PREMIUM TECH TOOL PTT V2.8.21 VCADS+DEVELOPER TOOL+APCI 2021/09 ( 1 PC )
Trucks software$85.00
Rated 0 out of 5
- DOOSAN DMS-5 3.1.3 [2023.11] diagnostic software 1PC
DOOSAN$106.00
Rated 0 out of 5
- 10 IN 1 FOR CAT SIS Caterpillar 2021 Full Service Dealer INCLUDING CAT 2019 C
CAT$110.00
Rated 0 out of 5
- Diamond Logic Builder DLB 2018
Navistar$40.00
Rated 0 out of 5
- DETROIT DDDL 8.14 SP3 – Detroit Diesel Diagnostic Link 8.14 SP3 2021 ( 1PC )
Detroit$73.00
Rated 0 out of 5
- download Hitachi Construction Machinery MPDr Ver 3.7.0.0 [10.2020] Diagnostic Software
Hitachi$76.00
Rated 0 out of 5
- PACCAR Engine Analyzer v1.3.0.6
PACCAR$55.00
Rated 0 out of 5
- VOLVO PREMIUM TECH TOOL PTT 2.7.30 Developer + Devtool + INSTALATION VIDEO!
Trucks software$60.00
Rated 0 out of 5
Related products
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
1000 & 2000 Gen 4$50.00
Rated 0 out of 5
- SERVICE MANUAL 3000 and 4000 Series Gen 5 ALLISON
Allison$18.00
Rated 0 out of 5
INTERNATIONAL ENGINES$29.00
Rated 0 out of 5
- SERVICE MANUAL BOBCAT 320-322
BOBCAT$65.00
Rated 0 out of 5
- SERVICE MANUAL MACK MP7 2007
MACK$30.00
Rated 0 out of 5
- SERVICE MANUAL DETROIT Earings – Technicians Guide
DETROIT$18.00
Rated 0 out of 5
CARRIE$20.00
Rated 0 out of 5
- SERVICE MANUAL DETROIT DIESEL DDEC II to III-IV Conversion
DETROIT$18.00
Rated 0 out of 5
- SERVICE MANUAL International Engines MaxxForce 7 (2007-2009)
INTERNATIONAL ENGINES$31.00
Rated 0 out of 5
- SERVICE MANUAL Eaton Fuller® HD FR/FRO TransmissionsTRSM2400April 2013
TRUCK MANUALS
Rated 0 out of 5
- SERVICE MANUAL VOLVO D13 (2009)
TRUCK MANUALS$25.00
Rated 0 out of 5