- Manuals
- Brands
- BendPak Manuals
- Scissor Lifts
- MD-6XP
- Installation and operation manual
Portable mid-rise
Hide thumbs Also See for MD-6XP:
- Service manual (24 pages)
1
2
Table Of Contents 3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
-
- Contents
- Table of Contents
- Troubleshooting
- Bookmarks
Table of Contents
-
Table of Contents
-
Introduction
-
Shipping Information
-
Safety Considerations
-
Faqs
-
Components
-
Specifications
-
Installation Checklist
-
Installation
-
Operation
-
Maintenance
-
Troubleshooting
-
Wiring Diagrams
-
Labels
-
Parts Diagrams
-
ALI Store
Advertisem*nt
Quick Links
Download this manual
Installation and Operation Manual
Manual P/N 5900108 — Manual Revision F — March 2020
Models:
• MD-6XP
Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.
⚠
DANGER
Portable Mid-Rise Scissor Lift
Read the
product. Failure to follow the instructions and safety precautions in
this manual can result in serious injury or death. Make sure all other
operators also read this manual. Keep the manual near the product
for future reference. By proceeding with setup and operation,
you agree that you fully understand the contents of this
manual and assume full responsibility for product use .
entire
contents of this manual
1645 Lemonwood Dr.
Santa Paula, CA, 93060 USA
Toll Free: (800) 253-2363
Telephone: (805) 933-9970
bendpak.com
before
using this
Table ofContents
Advertisem*nt
Table of Contents
Related Manuals for BendPak MD-6XP
-
Lifting Systems BendPak MD-6XP Service Manual
(24 pages)
-
Scissor Lifts BendPak MDS-6EXT Installation And Operation Manual
Mid-rise scissor lift (68 pages)
-
Scissor Lifts BendPak MDS-6 Series Installation And Operation Manual
Mid-rise scissor lift (92 pages)
-
Scissor Lifts BendPak MDS-6EXT Installation And Operation Manual
6,000 lb. / 2,722 kg. capacity mid-rise scissor car lift (48 pages)
-
Scissor Lifts BendPak MDS-6EXTF Service Manual
Mid-rise scissor lift (25 pages)
-
Scissor Lifts BendPak MDS-6LP Service Manual
Mid-rise scissor lift (29 pages)
-
Scissor Lifts BendPak SP-7XE Installation And Operation Manual
Full-rise scissor lift (68 pages)
-
Scissor Lifts BendPak Quatra XR-12000L Installation And Operation Manual
Full-rise scissor lift (72 pages)
-
Scissor Lifts BendPak XR-12000 Installation And Operation Manual
12,000 pound capacity surface mountedfull-rise scissor lifts (44 pages)
-
Scissor Lifts BendPak SP-7XE Installation And Operation Manual
Full-rise scissor lift (80 pages)
-
Scissor Lifts BendPak SP-7XLF Service Manual
Full-rise scissor lift (35 pages)
-
Scissor Lifts BendPak P-6B Service Manual
Open center pit lif (31 pages)
-
Scissor Lifts BendPak LR-10000 Installation And Operation Manual
Low-rise scissor lift (44 pages)
-
Scissor Lifts BendPak Quatra XR-12000AL Service Manual
Scissors alignment lift (58 pages)
-
Scissor Lifts BendPak LR-60 Service Manual
Low-rise scissor lift (12 pages)
-
Scissor Lifts BendPak P-6FB Service Manual
(29 pages)
Summary of Contents for BendPak MD-6XP
- Page 1 Portable Mid-Rise Scissor Lift Installation and Operation Manual Manual P/N 5900108 — Manual Revision F — March 2020 Models: • MD-6XP Designed and engineered by BendPak Inc. in Southern California, USA. Made in China. ⚠ entire before Read the contents of this manual using this product.
- Page 2 Copyright. Copyright © 2020 by BendPak Inc. All rights reserved. You may make copies of this document if you agree that: you will give full attribution to BendPak Inc., you will not make changes to the content, you do not gain any rights to this content, and you will not use the copies for commercial purposes.
-
Page 3: Table Of Contents
Installation Introduction This manual describes the MD-6XP, which is a mid-rise, frame-engaging, scissor Lift that is portable and comes with a small footprint designed for narrower bays and low-ceiling garages. The MD-6XP can raise Vehicles up to 6,000 lbs (2,722 kg). -
Page 4: Shipping Information
Make a visual inspection of the product before using it. Check for damage or missing parts. Do not use the product if you find any issues. Instead, take it out of service, then contact your dealer, email support@bendpak.com, visit bendpak.com/support, or call (800) 253-2363. •... - Page 5 • Use of the product for purposes other than those described in this manual. • Modifications to the equipment without prior, written permission from BendPak Inc. • Injury or death caused by modifying, disabling, overriding, or removing safety features. •...
-
Page 6: Faqs
Q: The MD-6XP is called a “mid-rise” Lift, what does that mean? A: It means that the MD-6XP can raise a Vehicle up to three and a half feet off the ground, which is higher than low-rise scissor lifts, but not as high as full-rise scissor lifts. -
Page 7: Components
Short Hydraulic Hose. Connects the two Hydraulic Cylinders on the Lift. • Safety Locks. Hold the Platform in place, once they are engaged. The MD-6XP has three Safety Lock positions, which lets you select the right Vehicle height for your needs. -
Page 8: Specifications
Specifications MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020... - Page 9 For height comparison only; *** Lowering is much slower with no Vehicle on the Lift. **** Must specify at time of ordering. Specifications subject to change without notice. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
-
Page 10: Installation Checklist
Installation Checklist Following are the steps needed to install an MD-6XP Lift. Perform them in the order shown. ☐ 1. Review the installation Safety Rules. ☐ 2. Make sure you have the necessary Tools. ☐ 3. Select the Installation Site. -
Page 11: Installation
Installation This section describes how to install an MD-6XP. Perform the steps in the order listed. ⚠ Use only the factory-supplied parts that came with your Lift WARNING . If you use parts from a different source, you void your warranty and compromise the safety of everyone who installs or uses the Lift. - Page 12 Select a Site The MD-6XP is portable, so you may be moving it and using it at a variety of locations. Keep the following in mind when selecting a location for your Lift: • Clearance. You must have adequate space on all sides, plus enough space above for the Vehicles you will be raising.
- Page 13 Extra distance is required on both ends so that you can drive Vehicles onto and off of the Lift in either direction; if your layout only allows Vehicles to be driven onto and off the Lift from one direction, then less space is required at the non-approach end. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 14 2. Attach the Handle to the Base using a Bolt, Washer, and Nut per hole. Use M6 x 1.0 x 30 mm Bolts. 3. Keep the Tow Cart in an accessible area for future use. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 15 Nuts and Bolts. 4. Use an appropriate tool to securely tighten the Nuts and Bolts. Important: Do make any connections to the Power Unit at this point. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 16 Hydraulic Hoses and Fittings on the Lift, making your new Lift inoperable. Your Lift is shipped with clean components; however, Bendpak strongly recommends that you take secondary precaution and clean all Hydraulic Hoses and Fittings prior to making connections. It is better and less costly to take these extra steps now so that you do not need to take your Lift out of service later to fix issues that could have been prevented at the time of installation.
- Page 17 If you put too much, the excess liquid will be pushed out when the Fitting is tightened; use a rag to wipe the excess. 3. Tighten the Fitting into the connector; do over tighten the Fitting. 4. Allow the manufacturer-recommended curing time before pressurizing the system. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 18 Connect the Hydraulic Hoses Hydraulic Hoses provide Hydraulic Fluid to the Hydraulic Cylinders, where it is used to raise the Platform. The MD-6XP comes with two Hydraulic Hose lengths: • Short Hydraulic Hose. Connects the two Hydraulic Cylinders on the Lift.
- Page 19 8. Connect the Curved end of the Long Hydraulic Hose to the Elbow Fitting on the Power Unit. Once all Hoses and Fittings have been attached, securely tighten all connections. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 20 Nut; keep it loose enough so that the Arm can move and pivot within the Channel. 5. Repeat Steps 2 through 4 for the remaining Lift Arms. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 21 If your Reservoir does not have the MAX/MIN markings, full is approximately .5 in / 12.5 mm under the Reservoir Cap. 4. When the Reservoir is filled, put the Reservoir Cap back on. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 22 Remember, all wiring must performed by a appropriate for your location. licensed, certified Electrician for this process. 2. Plug the Power Cord to an appropriate power outlet. 3. Begin using the Lift. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 23 High running amps that exceed the motor’s full load amps (FLA) rating may result in permanent damage to the motor. BendPak strongly recommends you exceed the rated duty cycle of the motor. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 24 If the Lift is shaking, moving erratically, or squeaking, repeat the procedure one more time. If you continue to have issues, refer to for assistance. Troubleshooting MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
-
Page 25: Operation
Check the Vehicle. Never exceed the Lift’s weight rating. Do not allow people inside a Vehicle you are going to raise. Make sure the Vehicle is not overbalanced on either end or either side. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020... - Page 26 When the Release Cam goes past a Lock Block, it makes an audible click when it hits the Base. 2. To use that Safety Lock, keep pressing Up for another half a second, then release Up. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 27 Lock Block it just passed. 4. If you miss the desired Safety Lock, there’s no problem; just try it again until you get it right. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 28 ⚠ WARNING When you raise a Vehicle with the MD-6XP, you are raising it using four Pads which grip the underside of the Vehicle at four points. You want to position your Pads under the manufacturer’s recommended Lifting Points because the manufacturer, by calling out those Lifting Points, is saying that if you raise the Vehicle at those points the Vehicle will be balanced.
- Page 29 7. Put the Lift Pads under the Vehicle so that they are directly under the Lifting Points for the Vehicle you are raising. If necessary, use the included Lift Pad Extensions for extra height. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 30 If you miss the desired Safety Lock, press and hold Up again and go for somewhat further past the desired Safety Lock. Release Up, then hold the Lowering Handle again to lower the Platform onto the desired Safety Lock. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 31 5. Push the Lift Arms in towards the Frame. This is so they are not in the way when the Vehicle is moved. 6. Carefully drive the Vehicle off the Lift. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 32 Move the Lift The MD-6XP is portable, which means you can move it around your work space. This can be done using the Tow Cart; the Tow Cart has a Tow Pin at the Base that hooks onto the Lift so you can move it around.
-
Page 33: Maintenance
Do not operate your Lift if you find issues; instead, take it out of service, then WARNING: contact your dealer, email support@bendpak.com, visit bendpak.com/support, or call (800) 253-2363, extension 196. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020... -
Page 34: Troubleshooting
Only leave the Lift either fully lowered or lowering the Lift). engaged on a Safety Lock. If you continue to have problems with your Lift, contact your dealer, visit bendpak.com/support, email support@bendpak.com, or call (800) 253-2363, extension 196. MD-6XP Mid-Rise Scissor Lift... -
Page 35: Wiring Diagrams
Wiring Diagrams 5585435 MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020... -
Page 36: Labels
Labels MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020... - Page 37 MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 38 MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
-
Page 39: Parts Diagrams
Parts Diagrams MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020... - Page 40 MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 41 MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
- Page 42 MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020...
-
Page 43: Ali Store
The ALI Store is your trusted source for workplace safety! Visit today and get the training and materials you need to work safely: www.autolift.org/ali-store/. MD-6XP Mid-Rise Scissor Lift P/N 5900108 — Rev. F — March 2020... - Page 44 1645 Lemonwood Drive Santa Paula, CA 93060 USA © 2020 by BendPak Inc. All rights reserved. bendpak.com...
